Axle Bearing Puller banner
Does Your Toolbox Need a New Member? Get Your Axle Bearing Puller Today
Work Smarter, Work Faster

Don't let a bad axle ruin your day!

Consider the following scenario: You’re on your way to work, and your car breaks down on the side of the road. Not only is it an inconvenience, but it can also be costly to have a tow truck come and haul your car away. One way to avoid this situation is to use an axle-bearing puller. This tool helps to remove the bearings from your axles, allowing you to replace them if they are worn out. The process is relatively simple, and it can save you a lot of money in the long run. So if you’re dealing with a bad axle, don’t let it ruin your day. Use an axle-bearing puller and get back on the road.

No Need to Call a Mechanic With Axle Bearing Puller

Many car owners are hesitant to tackle repairs on their own, fearing that they will end up causing more damage than they fix. However, there are a number of simple repairs that even the most inexperienced driver can handle, and replacing an axle bearing is one of them. With an axle-bearing puller, the entire process can be completed in a matter of minutes. Best of all, there is no need to call a mechanic, which can save a significant amount of money.

While an axle bearing puller is a fairly inexpensive tool, it can be a lifesaver when it comes to replacing an axle bearing. Usually, you don’t need much more than a basic understanding of car parts and a willingness to follow directions to be able to repair your car. With a few simple steps, anyone can replace an axle bearing, and avoid the expensive bill that comes with calling a mechanic.

But what exactly is an axle bearing puller? Well, it’s a tool designed specifically for removing bearings from their housings. There are several kinds of axle wrenches, and each one is for a different purpose—for example, there’s an axle bearing puller for motorcycle axles and one for car axles—but they all work basically the same way: they apply pressure to the outer race of your bearing while simultaneously pulling it out of its housing.

In short: if you want to save yourself some grief (and maybe even some money) when it comes time to

Axle bearing puller usage
The Convenience of Axle Bearing Pullers

A Must-Have Tool for Your Bearing Needs

If you’re looking to replace your car’s bearings, you’ve probably noticed that it can be a bit of a challenge to get them out. This is because they are installed in such a way that they’re held tightly by the axle hub, which means that they don’t just pop out when you try to loosen them with a wrench or hammer. If you want to avoid damaging your axle in the process, one tool that can help is an axle-bearing puller.

An axle-bearing puller is essentially a piece of metal shaped like a horseshoe with two ends: one end has a bolt sticking out of it and the other end has two grooves for holding onto the outer ring of your bearing.

You insert it into each groove on one side of your bearing until it reaches its tightest point, then use a hammer to tap gently on the bolt end until it pushes against both sides with equal force and loosens up enough for you to remove it from its housing without damaging anything else in your vehicle’s drivetrain system.

But here’s why: if you use any other kind of tool, like an impact wrench or an air hammer, there’s a good chance that when it comes time to put the new bearing in, it won’t fit right and won’t work properly.

That’s because they designed these bearings with specific tolerances in mind, and if they aren’t met exactly, it could cause problems down the road when something else goes wrong with the vehicle.

So don’t risk it—get yourself an axle-bearing puller today!

Pull out any bearing in an axle housing with ease!

Identify your needs and buy the best product.

Gear Bearing Puller
Used on a shaft to take off a gear.
Small Bearing Puller
Used for removing and installing bearings in the engine.
Inner Bearing Puller
This kind of puller can be either mechanical or hydraulic.
Axle Bearing Puller banner

Removal of Axle Bearing Puller

If you’re looking to remove an axle bearing, then you’ll need an axle bearing puller. This handy tool makes it easy to remove bearings without damaging the surrounding area. Here’s how to use one:

First, attach the jaws of the axle bearing puller to the outer race of the bearing. Make sure that the jaws are evenly spaced around the circumference of the race. Then, tighten the screw on the puller until the jaws are snug against the race.

Next, insert the shaft of the puller into the center of the bearing. The shaft should be long enough to extend beyond the race on both sides. Once the shaft is in place, turn the handle of the puller to begin extracting the bearing from its housing.

As you turn the handle, you’ll feel resistance as the jaws grip the bearing. Continue turning until the bearing is completely removed from its housing. Once it’s free, you can inspect it for damage and then either clean it or replace it as necessary.

An axle bearing puller is a handy tool that can make removing bearings quick and easy. But unless you take care of your puller, it can quickly become caked with dirt, grime, and rust. Here is a little advice to keep your puller healthy:

First, always clean your puller after each use. A quick wipe down with a rag will help to remove any build-up on the jaws or handle. Second, if your puller is starting to show signs of rust, coat it with a thin layer of oil. This will help to prevent further rusting and will keep the jaws working smoothly. Finally, if you will be storing your puller for an extended period of time, make sure to wrap it in a light cloth to keep dust and dirt from accumulating on it. These strategies ensure that your axle bearing puller will last for years.

Send Inquiry

Quick Quote
Use scenarios of shaft bearing pullers

It's For Taking Bearings Off of Axles

If you’re looking for a tool that will help you remove the axle bearings on your car, you’ve probably seen the word “axle” used in conjunction with “bearing” quite a few times. So what is an axle bearing puller? And how does it work? And when would you need one?

An axle bearing puller is a special kind of wrench that helps you remove the axle bearings from their housing. They usually have a long handle with an adjustable opening at the end, which allows them to accommodate different sizes of axles and bearings. Axle bearing pullers come in two main types: those designed specifically for front-wheel drive vehicles and those designed specifically for rear-wheel-drive vehicles.

There are many situations in which an axle bearing puller can be helpful—but there are also some situations where they aren’t necessary or even useful. Before you buy one, make sure to read through this list so that you know what situations require an axle bearing puller and which ones don’t!

So what kinds of situations call for an axle bearing puller? Well, here are just a few:

1) You have to remove an axle bearing from its housing

2) You need to replace an axle bearing with a new one

3) You’re servicing your car’s differential system and need to remove/replace a differential pinion gear

4) You want to install new bearings on your vehicle’s axles

All of these are perfectly valid reasons to need an axle bearing puller. And in each case, an axle bearing puller will make the job a whole lot easier. So if you find yourself in any of these situations, don’t hesitate to pick up an axle bearing puller and get the job done right.

Axle Bearing Puller Decrease Damage
Decrease Damage
Used to remove the axle bearings without damaging them.
Axle Bearing Puller Quick
Quick
Easily remove the bearings from the axle housing.
Axle Bearing Puller Safe to Use
Safe to Use
Easy to use and won't harm your car.
Axle Bearing Puller Convenient
Convenient
Can be used in tight spaces.

Why the Axle Bearing Puller is Essential for Every Mechanic?

When you need to replace your axle bearing, you might be wondering what this tool is and how it works. An axle bearing puller is a tool that allows you to remove the axle from your vehicle in order to change out the bearings.

This tool is typically made up of a metal base with an opening for your car’s axle shaft and a handle on the top of it. There are also clips that go around either side of the base, fastening themselves to the frame of your car to keep everything in place while you’re working on it.

You’ll need a jack stand or two in order to lift up one side of your car so that there’s enough room for you to work under there without the risk of falling off your jack stand and getting hurt. You’ll also need some extra hands to help hold everything steady while you’re pulling out the old bearings and installing new ones!

The way it works is pretty simple—you just slide it over your wheel and press down on the handle. This pushes the wheel up against the bearing and creates enough pressure to dislodge it from the axle. After that, you can just wait for everything to settle down so you can remove the wheel from your car.

Don’t worry about it—it’s not that hard to get the hang of once you start.

The need for an Axle Bearing Puller

If you’re a car repair enthusiast, the chances are pretty good that at some point in your life, you’ve taken apart the axle of a car. Doing it isn’t hard, but it might be tedious. After all, if you’re taking apart axles, then you’re probably in there for a reason—and that reason is probably that something is broken or worn out.

Are you tired of having to use your fingers to pull out your axle bearings? Wouldn’t it be nice if there were an easier way to get those bearings out?

Well, there’s good news: there is a tool for that!

The axle bearing puller is a simple tool that allows you to easily remove the axle bearings from your wheels. The process is simple: place the tool over the bearing, push down on it, and then turn it counterclockwise. That’s it! You can do it even if you have no experience or know-how.

You don’t have to worry about damaging your vehicle or having the axle bearing damage your vehicle when you use our tool—it’s designed to be gentle and easy on your vehicle.

It is essential for every mechanic

Every mechanic needs a puller. That’s just the way it is. Pullers are your best friend in the shop and they will help you get the job done right. There are many different types of pullers on the market, but one of the most common is an axle bearing puller.

When it comes to axle bearing pullers, though, don’t be fooled by their simplicity: They’re absolutely vital for getting those pesky bearings out of your axles when they need to be replaced.

Not only does using an axle bearing puller save time by eliminating other steps like drilling out rivets or removing nuts before you can remove bearings from their housings, but it also helps ensure that the bearings are removed evenly. This maintains the integrity of the axle itself, which is important for a number of reasons.

Time to get one for your workshop!

When you need to remove a wheel bearing from a vehicle, you’re going to need an axle bearing puller. These tools are designed to remove the wheel bearing from the wheel hub and pulley on your vehicle. They’re also useful for removing bearings from other types of machinery and equipment. If you want to do some DIY repair work, an axle bearing puller is a must-have tool in your workshop.

We know that axles are important parts of any vehicle—so don’t let them get stuck on you! Grab yourself an axle puller today at TOTALBEARINGS and get back to work in no time at all!

What is an axle puller?

An axle puller is a tool that allows you to remove bearings from axles. They’re typically used in vehicles, but they can also be used on bicycles or other machines that use axles.

How come axle pullers are so awesome?

Some of the benefits include being able to easily remove bearings from axles without damaging them or your machine, as well as being able to easily replace bearings with new ones when they’re worn out or damaged.

How do I use an axle bearing puller?

You should first make sure that the wheels are off of your vehicle, so you can access the axle housing. Then, you need to place one end of the spindle into the back of your car, and then use a crescent wrench or ratchet to tighten it down until it’s secure. Next, place the other end of the spindle into your puller and spin it until it clicks into place. Finally, remove the lock nut from your axle by hand or with an adjustable wrench, and remove any grease or oil before sliding out your old bearing. Then simply slide in a new one and put everything back together!

Why should I use an axle bearing puller instead of some other method?

The axle bearing puller is easier to use than some other methods because it doesn’t require any specialized tools or knowledge, and it doesn’t take much time or effort. You can use it right in your own driveway without having to go anywhere else for help or parts. You also won’t have any risk of damaging other parts of your car when using this tool because all its parts are designed specifically for this purpose.

What do they use to make this product?

This product is constructed from high-quality materials designed to last for many years and not break as easily as some other products.

Send Your Inquiry Today
Quick Quote
Scroll to Top